PROMISE TECHNOLOGY, INC. OCTET CONDUCTOR Card Type Hard drive duplicator controller card Hard Drives supported One master EIDE/IDE drive (eight target EIDE/IDE drives) Floppy drives supported None Data Bus 32-bit VESA Local Bus Card Size Full length, full-height card [Image] CONNECTIONS Function Location Function Location Primary connector to J1 Reserved connector - J4 Octet Station via do not use Cable1-IN Secondary connector J2 Reserved connector - J5 to Octet Station via do not use Cable2-IN Reserved connector - J3 Reserved connector - J6 do not use do not use USER CONFIGURABLE SETTINGS Function Label Position » Factory configured - do not alter J1 Pins 1 & 2 closed » Factory configured - do not alter J2 Pins 1 & 2 closed » Factory configured - do not alter J3 Pins 2 & 3 closed » Factory configured - do not alter J4 Pins 2 & 3 closed » Factory configured - do not alter J5 Pins 2 & 3 closed IRQ SELECTION (SECONDARY) IRQ JP1 JP2 JP3 JP4 10 Closed Open Open Open » 11 Open Closed Open Open 14 Open Open Closed Open 15 Open Open Open Closed Note: Users are advised not to change the default jumper settings. IRQ SELECTION (PRIMARY) IRQ JP5 JP6 JP7 JP8 10 Closed Open Open Open 11 Open Closed Open Open » 14 Open Open Closed Open 15 Open Open Open Closed Note: Users are advised not to change the default jumper settings. MISCELLANEOUS TECHNICAL INFORMATION The Octet Conductor controller provides the interface between host system and one Octet Station, where one master drive duplicates to eight target drives. OCTET STATION [Image] CONNECTIONS Function Location Function Location Cable connector - CN0 Cable connector - CN9 master CABLE1-IN Cable connector - CN1 Cable connector - CN10 target1 CABLE2-IN Cable connector - CN2 Start/stop button J2 target2 Cable connector - CN3 Power connectors - J3 target3 master Cable connector - CN4 Power connectors - J4-J7 target4 target Cable connector - CN5 Power switch J8 target5 Cable connector - CN6 Power supply J9 target6 Cable connector - CN7 Voltage selector J10 target7 Cable connector - CN8 target8 DIAGNOSTIC LED(S) LED Color Status Condition LED1 Green On Target drive 1 is active LED1 Green Blinking Duplication error on target 1or no hard drive 1 LED1 Green Off Target drive 1 is idle LED2 Red On Power is on to target drives 1 & 2 LED2 Red Off Power is off to target drives 1 & 2 LED3 Green On Target drive 2 is active LED3 Green Blinking Duplication error on target 2 or no hard drive LED3 Green Off Target drive 2 is idle LED4 Green On Target drive 3 is active LED4 Green Blinking Duplication error on target 3 or no hard drive LED4 Green Off Target drive 3 is idle LED5 Red On Power is on to target drives 3 & 4 LED5 Red Off Power is off to target drives 3 & 4 LED6 Green On Target drive 4 is active LED6 Green Blinking Duplication error on target 4 or no hard drive LED6 Green Off Target drive 4 is idle LED7 Green On Target drive 5 is active LED7 Green Blinking Duplication error on target 5 or no hard drive LED7 Green Off Target drive 5 is idle LED8 Red On Power is on to target drives 5 & 6 LED8 Red Off Power is off to target drives 5 & 6 LED9 Green On Target drive 6 is active LED9 Green Blinking Duplication error on target 6 or no hard drive LED9 Green Off Target drive 6 is idle LED10 Green On Target drive 7 is active LED10 Green Blinking Duplication error on target 7 or no hard drive LED10 Green Off Target drive 7 is idle LED11 Red On Power is on to target drives 7 & 8 LED11 Red Off Power is off to target drives 7 & 8 LED12 Green On Target drive 8 is active LED14 Green Blinking Duplication error on target 8 or no hard drive LED12 Green Off Target drive 8 is idle LED13 Red On Power is on to master drive LED13 Red Off Power is off to master drive LED14 Green On Master drive is active LED14 Green Off Master drive is idle LED15 Red On Octet Station is on LED15 Red On Octet Station is off